Industry News

Home / News / Industry News / 4707Q Brake Shoe Specifications: Heavy-Duty Fitment, Dimensions & Materials

4707Q Brake Shoe Specifications: Heavy-Duty Fitment, Dimensions & Materials

Fleet maintenance teams rebuilding 16.5-inch S-cam drum brakes on Class 8 tractors and heavy trailers reach for the 4707Q brake shoe more often than almost any other friction assembly in that size class. The combination of Rockwell Meritor axle fitment, a stable FMSI 4707 edge profile, and the Q-grade lining specification makes it the default replacement part for a large share of heavy-duty fleets. Getting the specification right matters because the shoe table width, lining radius, and roller-end tolerances determine whether the brake builds torque evenly or pulls the wheel end out of balance within the first few thousand miles.

What the 4707Q Brake Shoe Is

The 4707Q brake shoe is a steel foundation brake shoe designed for heavy-duty S-cam drum brakes with a 16.5-inch (419 mm) drum, using friction material cut to the FMSI 4707 edge profile. It converts air chamber torque into clamping force against the drum through the roller end and the anchor end of the shoe web.

Definition. The 4707Q is a steel shoe and lining assembly that matches the FMSI 4707 friction profile, most commonly fitted to Rockwell Meritor S-cam brakes on Class 8 trucks, tractors, and heavy trailers, with OE cross-reference Meritor 15224724.

In a typical wheel end, two shoes sit inside the drum. When the driver applies the brake, the S-cam rotates and pushes the rollers on the upper ends of both shoes outward, pressing the linings against the drum. The anchor pin at the lower end holds the assembly in place. That layout is why the roller pocket bore, the anchor bore, and the web spacing all carry tight tolerances in the 4707Q design.

Because the 4707Q operates in an air-braked system that must meet FMVSS 121 stopping-distance requirements, changing the shoe geometry or lining compound shifts wheel-end torque output and can disturb the axle brake balance.

Specifications at a Glance

Every 4707Q replacement shoe must match five critical dimensions to be a direct drop-in: drum diameter class, shoe web width, lining radius, roller-end bore, and anchor-end bore. The table below summarizes the values that define the 4707Q in heavy-duty service.

16.5 inDrum diameter
419 mmMetric equivalent
4707FMSI edge code
15224724Meritor OE
5 checks.Drum class, web width, lining radius, roller bore, and anchor bore define every 4707Q replacement.
Table 1. Core dimensional reference for the 4707Q brake shoe with typical heavy-duty values.
Parameter Typical Value Service Note
FMSI edge code 4707 Defines lining profile and table contour
Drum size class 16.5 in / 419 mm Heavy-duty S-cam drum brake
Lining width 200 mm (7.87 in) Confirm against axle generation
Lining attachment Riveted or bonded Riveted for relining, bonded for lower noise
Shoe table material High-strength steel Typical web thickness 6-8 mm
OE cross-reference Meritor 15224724 3222D lining classification
Actuation S-cam Two shoes per wheel end

These values represent the most common 4707Q configuration in Meritor 16.5-inch brakes. Late-model axles may use a wider table with the same drum size, so confirm the web width, lining thickness, and roller pocket size against the original shoe before ordering.

Materials and Construction Standards

The 4707Q brake shoe must hold its geometry through repeated hard stops that push lining surface temperature past 400 degrees Celsius. That is why the table is formed from high-strength steel, and why the friction compound is matched to the FMSI 4707 profile rather than chosen arbitrarily.

The Q suffix in the manufacturer's catalog identifies the lining quality grade and the profile revision; it is not a dimensional change. A Q-grade lining typically uses a non-asbestos organic or low-steel compound that keeps friction stable through normal and high-temperature service. Zhejiang Bangchi Auto Parts Co., Ltd. builds the 4707Q lined shoe by riveting or bonding the lining to the steel table, then checks the finished assembly against the FMSI profile before packaging.

Lining cycle note. A riveted 4707Q assembly can be re-lined several times before the steel table needs replacement, which lowers the per-mile cost of brake maintenance for fleets running high annual mileage.

Riveted linings are the fleet standard because the lining can be replaced and the steel table reused across lining cycles. Bonded shoes run quieter and sometimes last longer in the same service, but relining a bonded assembly requires removing the old adhesive layer. Casted brake shoes are available for applications that need a one-piece body with higher structural mass.

4707Q Lined Brake Shoe for Rockwell Meritor Axles with 16.5-Inch S-Cam Brakes4707Q Lined Brake Shoe for Rockwell Meritor Axles with 16.5-Inch S-Cam BrakesThis 16.5x7-inch lined brake shoe with 32 rivet holes matches FMSI 4707 and OE 152.24724, making it a direct replacement for many Class 8 tractors and heavy trailers.View Product →

Fitment and Axle Applications

The 4707Q is the go-to replacement shoe for Rockwell Meritor axles fitted with 16.5-inch S-cam brakes, which covers a large portion of Class 8 tractors, vocational trucks, and heavy trailer axles. The same FMSI 4707 edge code is used on comparable axle platforms from other OEM builders, so the shoe cross-references across multiple tractor and trailer applications.

Before matching the part, record three details from the existing shoe: the FMSI number stamped on the lining edge, the web width measured across the shoe table, and the roller-end bore diameter. Those three values are enough to confirm whether a 4707Q will drop in or whether a different variant is needed.

Fitment rule. If the FMSI number and the web width match the original shoe, the 4707Q will position the lining correctly inside the drum. This is the fastest way to confirm compatibility on the bench.

Zhejiang Bangchi manufactures the Rockwell Meritor version of the 4707Q with the 15224724 OE cross-reference, including the 3222D lining classification, so buyers can order by FMSI number or by OE number.

4707Q Brake Shoe with 15224724 and 3222D Lining Cross-Reference4707Q Brake Shoe with 15224724 and 3222D Lining Cross-ReferenceBuilt to Rockwell Meritor specifications, this brake shoe is identifiable by FMSI or OE numbers. It suits high-use fleets monitoring lining wear for timely replacement.View Product →

Wear Limits and Replacement Indicators

Replace the 4707Q when the lining is worn to 3.2 mm (1/8 inch) above the rivet head, or when the drum exceeds its maximum allowable diameter, whichever comes first. High-use fleets measure lining thickness at 10,000- to 20,000-mile intervals and schedule the replacement before the rivets can contact the drum.

Service life depends more on duty cycle than on calendar time. A line-haul tractor can accumulate 400,000 miles on a set of 4707Q shoes; a refuse truck or mining hauler may wear the same shoe out in 80,000 miles. The chart below shows typical replacement intervals for three duty profiles.

Line-haul 400k mi Regional 250k mi Severe duty 80k mi

Bar length represents typical service mileage before lining replacement for each duty profile.

Field rule. If the old lining measures at or below the rivet head level at any point, the shoe has been ridden past its safe limit and the drum must be checked for thermal cracking before a new shoe is installed.

Inspect the shoe and drum together at every brake service. A single oversize drum can double the wear rate of a new 4707Q shoe pair.

  • Lining at or below 6 mm remaining at any point across the arc, on moderate to severe duty fleets
  • Deep scoring or heat glazing over more than one-third of the lining surface
  • Roller pocket wear that lets the shoe shift sideways during a brake application
  • Anchor bore elongation that changes the seating angle of the shoe
  • Delamination between the lining and the steel table
4707 Brake Lining with WVA 19030/33 and 14 or 16 Rivet Holes4707 Brake Lining with WVA 19030/33 and 14 or 16 Rivet HolesThis 16.5x7-inch lining set is designed for riveted shoe replacement, offering consistent dimensions when produced under IATF 16949, protecting against batch variation.View Product →

Sourcing and Quality Considerations

A 4707Q brake shoe is only as reliable as the dimensional consistency of its production batch. When a manufacturer operates under IATF 16949, every lot carries inspection records for web width, lining radius, roller bore, and lining hardness, which protects fleet buyers from batch-to-batch variation.

Zhejiang Bangchi Auto Parts Co., Ltd., founded in 2016 by engineers with more than 20 years in brake friction, operates a brake shoe production line with an annual capacity of two million units and supplies OEM and aftermarket customers under IATF 16949 quality management. The company publishes products using the FMSI numbering system, so a 4707Q can be cross-referenced against distributor catalogs without ambiguity.

When evaluating quotes for 4707Q shoes, ask the supplier for three things: the FMSI edge code verification, the lining hardness range, and the dimensional report for the roller-end bore. A supplier that cannot provide these documents is not a qualified source for safety-critical brake parts.

Sourcing rule. Confirm the supplier can produce an IATF 16949 certificate, a FMSI profile report, and batch traceability for the lining lot before committing to bulk orders.

For fleets that prefer to keep or replace complete assemblies, the company also supplies lined shoe kits and repair kits with the same FMSI 4707 profile, allowing one purchase to cover the full wheel-end service. Learn more about the manufacturer's background on the company profile page, and review the FMVSS 121 structural analysis of the 4707Q unit for regulatory context.

Frequently Asked Questions

What does the Q mean in the 4707Q brake shoe?

The Q suffix identifies the lining quality grade and profile revision in the manufacturer's catalog, not a dimensional change. The dimensional identity of the shoe comes from the FMSI 4707 edge code and the web width.

What drum size does a 4707Q brake shoe fit?

The 4707Q fits heavy-duty S-cam drum brakes with a 16.5-inch (419 mm) nominal drum diameter, the most common size on Class 8 tractors and heavy trailers.

What is the Meritor OE cross-reference for the 4707Q?

The most common cross-reference is Meritor 15224724 with the 3222D lining classification. Confirm the web width and roller bore against the original shoe before installation.

Can a 4707Q brake shoe be re-lined instead of replaced?

Yes, if the steel table has not been distorted, the roller pocket is not worn, and the anchor bore still seats on the pin. Re-lining with the correct FMSI 4707 profile restores the assembly at lower cost than a complete shoe replacement.

Bottom line. The 4707Q brake shoe is a well-documented heavy-duty component. When you match the FMSI profile, web width, and roller bore, and source from an IATF 16949-certified manufacturer, the replacement performs consistently across the fleet.